Download
Catalogs and technical documentation
Fluidfit 2 ways hand valve male thread BSPT – HBVL-R – Tierre
The Tierre HBVL-R Fluidfit 2 ways hand valve male thread BSPT has a POM acetal resin body and EPDM seals and works up to 10 bar at 65 °C in continuous use (10 bar at 90 °C for 5 minutes max), with BSPT 3/8″ thread. Available for 10 mm metric tube.
Available product codes: HBVL10R03B.
Fluidfit 2 ways hand valve male thread BSPT – HBVL-R – Tierre
The Tierre HBVL-R Fluidfit 2 ways hand valve male thread BSPT is a 2 ways hand valve for metric tube with a push-in connection on one side and a BSPT male thread on the other. It must only be used in fully open or fully closed position.
Fluidfit products are designed for water, food and air contact but can also be used with selected gases, vacuum and other liquids; easy actions allow the tube to be connected and released quickly, saving time and expenses.
It is part of the Tierre Fluidfit fittings range, together with the Fluidfit bracket for HBVU-S hand valves HMCP and the Fluidfit elbow hand valve female thread BSPP HESV.
| Feature | Value / Specification |
|---|---|
| Maximum temperature | 65 °C for continuous use; 90 °C for short-term use (5 minutes max) |
| Maximum working pressure | 10 bar at 65 °C for continuous use (10 bar at 90 °C for short-term use, 5 minutes max) |
| Thread | BSPT 3/8″ thread |
| Tube (ØD) | 10 mm metric tube |
Maximum torque values for BSP, BSPT and NPT plastic threads given in the catalogue; seal threaded connections with PTFE (Teflon) tape only.
| Thread | 1/8″ | 1/4″ | 3/8″ | 1/2″ | 3/4″ |
|---|---|---|---|---|---|
| Max torque | 1.5 Nm | 1.5 Nm | 3.0 Nm | 3.0 Nm | 4.0 Nm |
Make sure the tube and the push-in system are the same size and cut the tube square with a proper tube cutter, such as the ETC tube cutter; the tube must be clean, without scratches, cuts or deformities. Insert it by hand up to the end stop, without tools, and pull it once without releasing the collet to check it is connected; then fit the locking clip between body and collet and push the tube in again.
To disconnect, completely eliminate the pressure from the system, remove the clip, push the collet towards the fitting body and pull the tube keeping the collet pushed. When using metallic tubing, always deburr the tube ends to avoid damaging the o-rings.
| Code | ØD | T (BSPT) | B | A | ØP1 | ØP2 | L1 | L2 | E1 | E2 | H | ØC | Weight (g) | Pcs/pack |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| HBVL10R03B | 10 | R 3/8 | 20.1 | 13.5 | 20 | 23.0 | 12.5 | 42.3 | 48.3 | 79.8 | 26.3 | 24.2 | 34.3 | 15 |
Dimensions refer to the technical drawing in the downloadable PDF data sheet; inch version dimensions are given as in the catalogue.
Technical data from the catalogue Tierre Fluidfit, fittings for potable water, drink dispensers and beverages, Rev. 3.0.