The Tierre HSTB Fluidfit bulkhead inline flow regulator has a POM acetal resin body, brass handle and lock nut and stainless steel needle, and works up to 10 bar at 65 °C in continuous use (10 bar at 90 °C for 5 minutes max). Available for metric tubes from 6 to 10 mm and inch tubes from 1/4″ to 3/8″.
Available product codes: HSTB0606B, HSTB1010B, HSTB1/4-1/4G, HSTB3/8-3/8G.
The Tierre HSTB Fluidfit bulkhead inline flow regulator is an inline flow regulator with bulkhead system: it allows a precise regulation of the flow acting outside the device, even when the regulator is placed inside.
It combines the catalogue versions: HSTB – Bulkhead metric flow regulator (metric tube); HSTB – Bulkhead inch flow regulator (inch tube).
Fluidfit products are designed for water, food and air contact but can also be used with selected gases, vacuum and other liquids; easy actions allow the tube to be connected and released quickly, saving time and expenses.
It is part of the Tierre Fluidfit fittings range, together with the Fluidfit elbow bulkhead flow regulator HSLB and the Fluidfit elbow flow regulator HSLU.
| Feature | Value / Specification |
|---|---|
| Maximum temperature | 65 °C for continuous use; 90 °C for short-term use (5 minutes max) |
| Maximum working pressure | 10 bar at 65 °C for continuous use (10 bar at 90 °C for short-term use, 5 minutes max) |
| Tube (ØD) | Metric tubes from 6 to 10 mm and inch tubes from 1/4″ to 3/8″ |
Make sure the tube and the push-in system are the same size and cut the tube square with a proper tube cutter, such as the ETC tube cutter; the tube must be clean, without scratches, cuts or deformities. Insert it by hand up to the end stop, without tools, and pull it once without releasing the collet to check it is connected; then fit the locking clip between body and collet and push the tube in again.
To disconnect, completely eliminate the pressure from the system, remove the clip, push the collet towards the fitting body and pull the tube keeping the collet pushed. When using metallic tubing, always deburr the tube ends to avoid damaging the o-rings.
HSTB – Bulkhead metric flow regulator (metric tube)
| Code | ØD | ØP | T | E1 | E2 | L min | L max | A | B | H | Weight (g) | Pcs/pack |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| HSTB0606B | 6 | 15.5 | M12 xP1 | 22.2 | 44.4 | 45.5 | 50.4 | 5.0 | 16.1 | 16 | 28.9 | 50 |
| HSTB1010B | 10 | 20.0 | M15xP1 | 26.1 | 52.1 | 52.7 | 58.4 | 6.0 | 19.7 | 19 | 54.0 | 25 |
HSTB – Bulkhead inch flow regulator (inch tube)
| Code | ØD | ØP | T | E1 | E2 | L min | L max | A | B | H | Weight (g) | Pcs/pack |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| HSTB1/4-1/4G | 1/4 | 15.5 | M12xP1 | 22.2 | 44.4 | 45.5 | 50.4 | 5.0 | 16.9 | 16 | 28.9 | 50 |
| HSTB3/8-3/8G | 3/8 | 20.0 | M15xP1 | 26.1 | 52.1 | 52.7 | 58.4 | 6.0 | 19.8 | 19 | 54.0 | 25 |
Dimensions refer to the technical drawing in the downloadable PDF data sheet; inch version dimensions are given as in the catalogue.
Technical data from the catalogue Tierre Fluidfit, fittings for potable water, drink dispensers and beverages, Rev. 3.0.